#Cateye enduro 8 programming how to
#Cateye enduro 8 programming code

I could get the MPH legend to flash like it was registering something, but the speed stayed at 0.0 and the Odometer didn't advance.

I took it off the mount and took it indoors, put a key across the terminals. Magnet is in the correct place and tightened to the spoke, and the sensor isn't loose. I got it home, spun the front wheel and sure enough nothing happened. All was fine for the first 2.3 miles of my 3.06 mile commute home, then water must have done something as I looked down and the dreaded 0.0 was displaying despite me doing about 20mph. It was tipping down outside, but not torrential or anything. It happened again early this morning on my way home from the night shift. It's got 02/10 stamped on the back which I assume is the manufacturing date, so it's 11 actual months old but I bought it in September. Mine is I presume the shield shaped new style one, here's a pic of it before installation. It worked for my ride to work on Tuesday night, stopped working halfway home on Wednesday morning and still isn't working today despite repeated faffing about and checking and rechecking that the various bits are working with a paper clip and multimeter.īefore anyone suggests it, I don't want to buy a REPLACEMENT! they may only be £16 but there is no reason for this one not to work!!!!!!! HELP. Why is my cycle computer spitting it's dummy out? The individual parts check out ok but it still doesn't work when clipped together. The mount contact plates can be lifted slightly with a sharp blade just to make sure they are within reach of the computer contacts but this still doesn't help. The mount and wire has been repaired in the past (soldered, not twisted together) but when a multimeter set to read continuity is used on the contact plates the sensor switch can be seen to close when the wheel magnet passes by, so again all ok. The spring loaded contact pins on the rear of the computer are moving freely and when rapidly shorted with a paper clip the screen registers the speed so no problems there then? In the last two weeks it has done it twice and having some time to spare I decided to investigate. It always starts working again without any interference from me either the next day or when the bike is next used so I have always put it down to a bad contact although removing and refitting the computer into the mount doesn't fix it at the time. The most frustrating time was about 3-4 years ago while doing the Manchester 100 mile when it stopped at about the 75 mile point I have had a Cateye Velo 8 for about 5 years and while it has been great and seems very accurate (you set the wheel circumference to the nearest cm so not really surprising) it has on very rare occasions stopped reading during a ride.

#Cateye enduro 8 programming code

Open up ActionLayer.mm and add the following code right after the +(id)scene method: So before we go any further, let’s give that a try and see what happens. There may be some of you out there that are thinking, “HUD?! I don’t need no stinking HUD! I’ll just add the labels directly to the layer!”

Never fear – HUD to the rescue! Why You Need a HUD

What’s worse – when you win or lose nothing happens except for a sound effect – there’s no way to retry! If you get hit by a laser as you play the game, you’ll notice that you take a hit – however there is nothing on the screen to show you your lives. Your goal is to avoid the lasers, and make it to the end! You’ll see this is a simple game where you tap to move, or double tap to jump. If you’re curious, this game was made in this and that tutorial, but I don’t recommend those tutorials for beginners. Start by downloading the sample game that we will be using for this tutorial.

#Cateye enduro 8 programming how to

This tutorial is for beginners to Cocos2D who have gone through the How To Make a Simple Game with Cocos2D tutorial, or have equivalent knowledge. In this tutorial, we’re going to take a Cocos2D game that has been made with a single scene and single layer, and add a second layer to use as a HUD. You might want to use the HUD to contain extra controls (like a joystick or buttons) or you might want to use it to display status information (like lives or score). A common question for beginners to Cocos2D is how to add a second layer to your scene to use as a Heads-Up Display, or HUD.